Відео

Graçias!

Thanks, Keith! Youda gouda 🧀

Good video

Just wanted to say thank you. It's 930pm here and cold as heck. Furnace has been running like crap and finally stopped working altogether. Your video helped me get my igniter set and cleaned the nozzle and it's back running good.

Most helpful, thank you.

My nozzle is stuck I can't fkin get it off. Can't find a replacement anywhere for the entire piece either

Looking to add a pressure tank to a city water supply. Is it basically the same installation without the well pump?

👍👍🇨🇦✌️🇨🇦✌️🔧🔧

How can I increase the speed of my submersible pump?

Just get you one of those orange plastic Beckett Z gauge my go to

Great video! Thanks for you time doing it. I was looking for something like this. I wonder if you could/don't mind to share the document used to ilustrate the video. Would be nice to have that information printed for the next guy who will be in cherge of this Oil Furnace that I'm troubleshooting.

Sa...kusheto

Back in the 70’s I was in the Air Force in northern Maine and worked in the heat shop. Everything was oil fired back then, boilers and warm air. We spent most of the summers cleaning and PM’ ing. The heating system for the base grade school and a few other bigger buildings used a big rotary type main burner, with a .75 gph gun type burner as a pilot. I think it was about 1990 before the Bunker C smell left my body.😄 Your oil burner videos bring back good memories.

I like your style of making a video .your calm.... you don't add a bunch of unnecessary information direct and to the point very professional thank you

i have a problem with my Pump it starts and cut off after a minute,what could be the problem

After removing my nozzle, a metal rod was inserted behind the nozzle. Is that normal and why was that there?

A I’ve got a question? Will this boost city water with out using a pump. Just using the pressure in the tank to boost the water.

Great video , you didn’t explain the ongoing painful life of an oil burner mechanic being on call 🤣🤣🤣 let’s not forget the never ending winters for us in the trades 🤟

answer him on the 2 hot wires and why they don't need a neutral. the cycles are out of phase with the other and this allows them to use each other as a neutral

Awesome video! PleAse no music next time!

Great Video, Well Done. Been on the nozzle - electrode rodeo ride many times in 40+ yrs. Often finding undersized nozzles via homeowner penny pitching. In many areas homeowners seek budget fuel from bulk carriers lacking service contacts, sometimes they receive cocktailed oil #4 - #2 mix. #4 oil still around, #6 totally gone. "Todd" rotary cup burners almost extinct. Myself as LMP having oil, pay my provider for service contact as insurance when I'm out of town. Wife calls - they run, service guy always gets a $50 tip, no matter what. Once my oil guy [good friend] came to set a few mouse traps, wife was standing on a chair freaking out when I was out of town. Thereafter got a cat from the shelter.

Would you need to set electrodes if just changing the nozzle

At 3:28 you tested the windings . When the needle of the meter moved ,was that a good result or not ? Or should you expect that to happen ? Very interested

Thanks a ton Keith and your instructional vids are always the best. Wanted to replace and set the electrodes on my old Beckett oil gun and this vid was exactly what I needed. Thanks again.

Clear concise accurate video. thanks very much

You saved my oil furnace bro, my gaps were completely off to the point that my furnace was stalling and also puffing out black nauseating smoke. With this my furnace is running like the 50yr old champ it once was. ❤

Watching, beautiful oil burner electrodes invention, thanks for sharing

Thank you

Why not use a nozzle wrench?

You didn’t use the electrode gauge correctly when you set the 1/2 inch above the nozzle at 4:24. The center mark on the gauge lines up with the center of the nozzle. You used one of the outer lines on the center of the nozzle. The gauge also shows the distance ahead when you use the gauge, so you don’t need a separate ruler. If you look at your video at 4:24 you can read the gauge. The electrodes always line up on the + marks which show the proper position of the electrodes.

So is the home owner responsible for that set up? If so how much would that run me in parts?

Was kostet so ein bruner

What’s the consensus about the insulation foam under heavy loads (like a truck moving in and out every day). I imagine that eventually the foam gets squished and subsequently the floor starts cracking.

I can do this too

as this video 8ish yrs old, I hope you read this... I'm a forced into retirement former builder/carpenter/cabinet maker, disabled, so Residential anything, isn't new to me...on a very tight, limited budget...my oil furnace been acting up, not firing...diagnose igniter transformer, still have spark, come to conclusion, it the igniter leads..., watch another video on how to access the nozzle and leads...watch your video on rebuilding...go take out leads/nozzle plate...holy crap, leads so old, the points are burned off, they nubs, not points, lol. 30 mins later, trip to plumbing supply warehouse, new leads, even came with a Becket gap gauge, nozzle cleaned, leads installed, gapped....reinstall everything...hit reset button...voom...on comes the furnace instantly...since then, it's cycled on a cpl times...appears that was my problem...Thank You for this video, it cost me $41 in parts, a total of an hr, incl trip to plumbing supply.....saving me an easy $175, $200 service call, + parts

Thanks when I went to HVAC school we use to use a carpenters wood ruler to set gap and distance. Now I should look for a gauge like you showed easier I’m sure

Awesome video!

i appreciate the concise information and very good demonstration.

Nice

Question. Would installing a 20gal pressure bladder tank under my house with a check valve before make my water pressure make more steady water since my well doesn't have a pressure tank? I have no way to install a switch or any electrical add ons to the tank.

Can u believe that you made this video 8yrs ago & you just helped me out BIG TIME! 1/8", 1/8", &1/2" now I'll never forget it Thank you...now if I can just figure out y my Beckett oil pump keeps stopping or flowing? Oil pump is only 1yr old & furnace shut off so I figured I'd just make sure it's getting oil & it does come out of the bleeder valve for a few seconds then nothing? I'll let it sit for a few minutes & again it acts like it's going to give me a good flow but then flow completely just fades away? But hay I'll figure it out.

YA KNOW YOU SAVED ME 3GRAND SHOWING ME HOW TO FIX THAT. tHANKS sorry for the caps I was excited.

Ok good

U just saved my ass. Heard my furnace not ignite and checked my electrodes the tips were burnt off and way out of adjustment. Took them to the bench grinder to make a nice point and adjusted them. Hit the reset button and it's back burning better than it has in years.

Bunerr ke bare me bataye

Good video but I wish he showed when he set the electros in front of the nozzle. he cut that part out

I like the mariocart music lol

Ccccccccccccccccccccccc

I just received my waste oil burner package similar to yours. How would I safely connect the ignitor module for the electrodes.

What does it feel like when spinning the shaft with your fingers